Power the unit off. Unplug the power supply from the back of the base. Wait 1 minute. Press the Power button to turn the unit on. When your unit is powered back on, it will perform a clean cycle. Once the clean cycle is complete, the unit should go back to blue ready status. Attempt to initiate onboarding again by pressing the Cycle and Empty ...To troubleshoot the blue blinking, let's start by power cycling your unit: 1.) Leave your unit powered ON with the blue blinking light engaged & Unplug your power supply from the base 2.) Wait 10 seconds then plug the unit back in 3.) Allow the unit to complete a start‐up cycle. If the light is …If your unit has a blue light bar with partial yellow flashing or the unit will not cycle, this indicates that the scale has been triggered for more than 30 minutes. You will also receive a notification on your phone if you use the Whisker App. Place the unit on a firm, level surface. Avoid soft, uneven, or unstable flooring for accurate weight ...Exact same issue here. It stops upside down with the yellow light flashing insanely fast. Only solution is to unplug it, plug it back in and watch it spin 1.5 rotations and it will be back to normal. Until the next time. And Litter Robot doesn't seem to help. Mine is still under warranty.The Litter-Robot 3 is equipped with a cat sensor that detects when a cat enters and exits the globe. If the cat sensor has been continuously activated for 30 minutes or more, either by a cat that won’t leave the globe or by too much weight in the unit, the timing light will flash red.Hi! I require your help regarding a problem I'm encountering. Description: I received my litter robot on January 7 2020. I plugged it in but kept it turned off for the first few days and would manually run the clean cycle because my cat was just under the weight required to make the product function properly. As soon as my cat passed the required weight I turned it on and noticed that the ...Litter-Robot 3 Connect. First post, my LR3 was working fine. I pressed the cycle button and all of a sudden it quit. The keypad does absolutely nothing. The blue light is on. I have pressed every button. I have taken the keypad off and attempted to clean it and reinstall. I plug it in and it goes straight to solid blue and nothing.If your Litter-Robot 3 is displaying a yellow light flashing slowly, this indicates a cycle has been interrupted either by the cat sensor or bonnet removal. Press the Reset button to resume the cycle. If your unit returned home and displays a solid blue light, you've been successful.The Litter-Robot is equipped with an Anti-Pinch safety feature to make the Litter-Robot extra safe for your cat. While cycling, if a potential pinch condition is detected, the globe will stop and reverse direction for 2 seconds. The yellow light will begin flashing quickly, about four times per second. You will also receive a notification on ...Litter Robot III flashing blue and yellow lights that won't go away; Litter Robot 3 - DFI sensor again and now additional power button issue; Litter robot 3 - blue light flashing followed by rapid flashing yellow light; Litter robot 3.Blue light flashing constantly.Robot stopped cycling; Litter-Robot 3 doesn't work (blue blinking light)r/litterrobot. •. BootleggerBill. Help! Rapidly flashing yellow cycle light. Our LR3 connect is displaying a rapidly flashing cycle light and will not work. I have completely dissembled and deep cleaned. I paid special attention tot he pinch detector and DFI areas, making sure that the pinch detector can move freely and the DFI sensor is clean.Litter-Robot 3: Buttons and lights. Control panel buttons . Power. Press and release the Power button to turn the robot ON of OFF. The robot will begin a clean cycle when power is turned on. ... Blue & red flashing sequentially: Motor detects obstruction or jam during counter-clockwise rotation. Learn more. Blue, yellow, red flashing sequentially:i got this litter robot 3 last night on FB marketplace and saw it cycle multiple times. when i went to set it up today in its spot, the yellow light immediately started flashing upon plug in and it hasn't stopped. i can sometimes get the blue light to come on, and when a cat gets in it goes red and then that doesn't go off. i haven't been able to get it to cycle at all this morning. If your unit has a blue light bar with partial yellow flashing or the unit will not cycle, this indicates that the scale has been triggered for more than 30 minutes. You will also receive a notification on your phone if you use the Whisker App. Place the unit on a firm, level surface. Avoid soft, uneven, or unstable flooring for accurate weight ... BEFORE DOING THIS BYPASS HACK:Be sure to do the usual fixes first.. Clean plastic pinch detector part that flexes first (the cracks), then clean both sides o...If litter robot is flashing blue, yellow and red then this means it cannot find the dump position. What the video for the fix! If litter robot is flashing blue, yellow and red then this means it ...Sep 11, 2018 ... The red blinking light indicates CATS (the cat sensor) is detecting excess weight for more than 2 minutes. In this comprehensive tutorial ...If your Litter-Robot 3 is displaying a flashing red light or you are receiving cat sensor fault errors via the Whisker app, please follow the steps in this video to …Litter-Robot 4 user? Visit our support guide upon troubleshooting Litter-Robot 4 lights. Litter-Robot 3 lights: Quick reference guide. If you’re seeking for a quicker reference guide on view of Litter-Robot 3 lights, download the electronic guide here or click on of image below. Litter-Robot 3 flashing blue lightA 3-second long press enables or disables cycle delay setting mode. Connect button . Press the Connect button to turn WiFi ON or OFF. 1. WiFi OFF is indicated by a white light adjacent to the Connect button. 2. WiFi ON and connecting is indicated by a blinking blue light adjacent to the Connect button. 3.Emptying the waste drawer when indicated is important to ensure that your Litter-Robot continues to cycle automatically. Troubleshooting. A flashing blue light is normal, indicating the waste drawer is full. If your unit displays a flashing blue light or you received a “drawer full” notification in the Whisker app, please follow these steps:Hello. I'm new to the forum. I bought Litter Robot 2 years ago and till now was grand. nearly just stopped working. When I connect it to power blue light is flashing and after pressing reset button yellow light starts flashing rapidly. Robot will not move at all. I cleaned pinch sensor metal plates as I thought they might be dirty but no joy. Checked everything and seems to be ok. Can not ...Power the unit off. Unplug the power supply from the back of the base. Wait 1 minute. Press the Power button to turn the unit on. When your unit is powered back on, it will perform a clean cycle. Once the clean cycle is complete, the unit should go back to blue ready status. Attempt to initiate onboarding again by pressing the Cycle and Empty ...Litter-Robot 3 Connect. Tagged as LR3 Connect but this is not the Wi-Fi enabled model. I have the Litter Robot 3 and I keep getting sequentially flashing red and blue lights. This combination isn't in the manual so I'm not sure what to do. The robot is away from walls and perfectly level. There is nothing under the robot.Litter-Robot 3 flashing blue daylight. ... Litter-Robot 3 flashing red light. A solid ruby light on your Litter-Robot 3 control panel means that the cat sensor was activated by to cats entered an globe while the unit was ready for getting. This unit is counting down to a clean cycle, depending on your set wait time (3, 7, instead 15 …Mar 6, 2017 ... http://www.litter-robot.com/ We want your cats to love their Litter-Robot. This is why we have thought of unique Litter-Robot features that ...Submit support request. Select a category for your ticket. Select a sub-category for your ticket. Please describe your issue. Got questions or issues? Contact Litter-Robot Support today. We're dedicated to ensuring a seamless experience for you & your pet.Litter robot was saying drawer full all the time, cleaned the DFI and still saying full. But now when I try to reset and turn manually I'm getting rapidly flashing yellow light. I had a go at cleaning the pinch detectors but no change. ... where you can allow it to cycle when ready, or simply press the "Reset" button to put it black to blue ...Quick question. I got a litter robot 2 for about 2 years. It stop working today. The "empty" and "cycle" bottoms doesn't work but only reset bottom works and "ready" is flashing blue. If I push the "reset" bottom, "cycling" is flashing yellow in 4 times per sec. The problem didn't solve after I cleaned up pinch pins.Community for all things Litter-Robot. Post your experiences, tips, tricks, and hacks. Members Online • NoCheek8681 . Litter Robot 3 yellow light flash just 2 times and die Litter-Robot 3 ... I attached a video to show what it is doing with the yellow light just flashing 2 times after we plug the unit… anyone knows what the issue is? ShareShort press the Reset button, then short press the Cycle button to run a Clean cycle. After your Litter-Robot cycles, it should return to the Home position, displaying a blue light bar. Successful: If your unit displays a blue light bar, you've been successful. Unsuccessful: If you are still seeing a red light bar with partial white flashing ...The Litter-Robot 3 is equipped three LED lights to indicate certain statuses and faults with your unit. If all three of these lights are flashing in one of three combinations, it is an indication of a globe position fault.How to fix the blinking blue light on the litter robot open air that says the tray is full when it's not. I hope this helps.Blue light blinking - Litter robot 3 - Domestic Robots - RobotShop Community. Help & Support Domestic Robots. Mariagav July 1, 2023, 10:15pm 1. Hi, I need help with my litter robot 3 please. The blue light is blinking although the waste drawer is empty. The other buttons do not react to pushing except the on/of one.Fix 1: Empty the waste drawer. If the blinking blue light is caused by a full waste drawer, the fix is simple: empty the drawer and reset the unit. The waste drawer is located at the bottom of the Litter Robot, …This may take up to 30 minutes to complete. You will see a single white light blinking on your unit's control panel while your robot's firmware is updating. Once the update is complete, your Litter-Robot should be ready for use. Successful: If your unit displays a blue light bar, you've been successful.Troubleshooting Common Litter-Robot 4 Errors & How To Fix. Key Takeaways. 1. The most common issues with Litter-Robot not cycling stem from power issues, the type of litter used, foreign objects, or software malfunctions. 2. Regular maintenance, including weekly waste drawer checks and bi-weekly thorough cleaning, ensures optimal performance. 3.View the Litter-Robot 3 Waste Drawer Liner Installation Video. To change the drawer liner in Litter-Robot 4, pull out the drawer and dispose of the soiled liner. Open a new waste drawer liner and wrap the edges over the rim of the waste drawer. Push the remainder of the bag into the bottom of the waste drawer. Check out the Litter-Robot 4 Waste ...How to fix the blinking blue light on the litter robot open air that says the tray is full when it’s not. I hope this helps.MOD. Can't get flashing blue "drawer full" light to clear. So I've got a recurrent problem with the flashing blue light, which the instructions and research tells me means the waste bin/drawer is full. But I've completely emptied it several times, and still the flashing blue light persists. If I press the "reset" button it will turn to solid ...Good morning, Quartz readers! Good morning, Quartz readers! Japan’s lower house votes on a new immigration bill. Opposition parties are protesting the expected passage of prime min...Oh my gosh, I've been having the exact same issue!! I purchased the Litter Robot from the canadian site as soon as it became available (October 29th). I've been struggling with the drawer full indicator for weeks and have been too busy to contact support. Like you ArcticThunder, I only have one DFI sensor! It is the one on the right. I noticed this very early after getting my unit and ...Following. You will have dislodged the Hall Effect Sensor, located left side of motorwell. Its 2 sets of 3 wires taped to a small black stand. You need to put the 2 black feet into 2 upright pillars with holes in them, left side of motorwell. Thank you.Watch on. If Litter-Robot 3 globe becomes jammed or overloaded when rotating clockwise, the motor will stop and reverse for 5 seconds. The unit will start to cycle again after 15 seconds, to attempt to return to the Home position. If after three attempts, the unit is unable to cycle, the globe will return to the Home Position and the control ...Toll Free: 877-250-7729 www.Litter-Robot.com Ongoing Maintenance Empty the Waste Drawer when indicated by the flashing blue light on the Control Panel. How often you will need to empty the Waste drawer depends on the number and size of your cats. For two average-sized cats, twice per week is typical. For a singleIf Litter-Robot 4 has a blue light bar with a yellow blinking light adjacent to the Connect button, this indicates that the unit is in Onboarding mode and waiting to be connected to the app. You can now proceed with the onboarding process within the Whisker App to finalize connection.Community for all things Litter-Robot. Post your experiences, tips, tricks, and hacks. Members Online • PWIest2016 . LR3 stuck upside down, flashing blue light User Experiences My LR3 is stuck upside down with the blue light flashing. I turned it off, unplugged it, pushed various buttons and combinations, cleaned it, wiped the sensors and ...So I am having this issue again!!! My litter robot 3 had been flashing blue light and then yellow light (very fast) after pressing the reset button. I’ve read some troubleshooting to check for the metal pinch bars to be in contact all the time. I’ve tried to clean it and it appears to be in contact as well. The pin is not corroded as well.Step 10: Manual Cat Sensor Activation. Press on the Globe just above the entrance in a forward and downward direction—just press and release. The blue light should turn off and the red light should come on. You've activated the Cat Sensor to simulate your cat entering the Globe, then exiting. Allow the Wait Time (3, 7, or 15 minutes ...During each Clean cycle, the DFI sensors will measure the level of waste within the waste drawer as the waste port passes over the waste drawer. Once a full waste drawer is detected, the unit will indicate it is full with a flashing blue light bar. You will also receive a notification on your phone if you use the Whisker app.These sensors detect when a cat has entered or exited the unit. If your unit has a flashing red light bar or the unit will not cycle, this indicates that the cat sensor has been triggered for more than 30 minutes. Successful: If your unit returned home and displays a blue light bar, you've been successful.Litter-Robot 3 flashing blue daylight. ... Litter-Robot 3 flashing red light. A solid ruby light on your Litter-Robot 3 control panel means that the cat sensor was activated by to cats entered an globe while the unit was ready for getting. This unit is counting down to a clean cycle, depending on your set wait time (3, 7, instead 15 …I've had my litter robot 3 only around 6 weeks the last couple of weeks its been problematic with either flashing blue lights or flashing yellow lights, usually following cleaning guidlines resolves the issue despite no debris or dirt around the sensors after a couple of goes. Today it has a flashing blue light which wont clear, I cannot ...My Litter Robot won't reset. The blue light is constantly flashing. When reset is pressed the yellow light then flashes. It pinch sensor has been cleaned and they are touching. The DFI sensors have been cleaned. Help!!! Thank you so much in advance for your help!1. When your cat exits Litter-Robot, a timer counts down, allowing the litter to clump before a clean cycle begins. 2. During the clean cycle, the globe slowly rotates. The patented sifting process separates the clumps from the clean litter. 3. The clumps are deposited into a sealed waste drawer below. 4.Jun 12, 2018 · robotshopTech June 12, 2018, 3:52pm 1. If your robot has problems with the yellow blinking light, please follow the troubleshooting below to determine whether the issue is due to excess weight, the bonnet connection, or the Anti-Pinch safety feature: *The blinking yellow light will switch to blinking red after 2 minutes if the cat sensor (CATS ... Reply. bitchassslutasswhore • 10 mo. ago. When I get the yellow flashing lights, I lift the globe, vacuum out the litter, reset it in the right position, then I unplug it from the back of the box. Before plugging it back in, I hold in the cycle button, plug in while holding the button in, release, and it works again. Might help you too.Litter-Robot 4: Light codes guide. Litter-Robot 4 control panel features 5 buttons and an LED display for easy operation. Blue flashing. If your unit's light bar is flashing blue, this indicates that the waste drawer is full. Empty the waste drawer, press the Reset button, then press the Cycle button. Learn more.I’ve had my litter robot 3 only around 6 weeks the last couple of weeks its been problematic with either flashing blue lights or flashing yellow lights, usually following cleaning guidlines resolves the issue despite no debris or dirt around the sensors after a couple of goes. Today it has a flashing blue light which wont clear, I cannot ... Our litter robot was Flashing Yellow Slow & Fast, then Fast Flashing Blue despite being empty and lastly just Random Lights. Watch for the solution to this, ... Step 10: Manual Cat Sensor Activation. Press on the Globe just above the entrance in a forward and downward direction—just press and release. The blue light should turn off and the red light should come on. You've activated the Cat Sensor to simulate your cat entering the Globe, then exiting. Allow the Wait Time (3, 7, or 15 minutes ...If your Litter-Robot 3 is displaying a yellow light flashing slowly, this indicates a cycle has been interrupted either by the cat sensor or bonnet removal. Press the Reset button to resume the cycle. Success: If your unit returned home and displays a solid blue light, you've been successful.To troubleshoot the blue blinking: Remove the drawer from the unit and press RESET. If the unit goes to solid blue, press the CYCLE button. The unit should start its cleaning cycle and goes back to solid blue. If it did, the issue must be caused by the drawer liner not being properly tucked into the tabs. Please check the following video:From the Home position, press the Power button to turn the unit off. Press the Power button to turn the unit back on. Litter-Robot will perform an initial Clean cycle, and the cat sensor will take a new measurement of the unit's weight. Success: The Litter-Robot should return home displaying a blue 'ready light' status.How to fix the blinking blue light on the litter robot open air that says the tray is full when it’s not. I hope this helps.Hello, I am again experiencing this issue: my Litter robot 3 is stuck with a blinking blue light. If I press reset, the yellow light starts blinking fast and the blue goes off. Another press of the reset button and the blue light starts blinking again and so on. I replaced the pinch detector pins and drawer full sensors a year ago (see Litter Robot 3 Keeps Getting Stuck (Help) - #12 by Ebram ...Having issues with my litter-robot 3. Upon starting cycle (now when power is first turned on), the bonnet will rotate through fully in one direction, stop for a second or two when the dump opening align, then tries to continue rotating in that same direction for another few seconds then completely stops. A rapid flashing yellow light is then shown.Follow these steps to update your Litter-Robot's firmware: 1. In the Whisker app, select your Litter-Robot 4 unit from the dashboard. 2. Tap on the Settings gear in the top right corner. 3. On the Robot Settings page, tap Firmware Updates. 4. On the Firmware Updates page, tap Update to begin the update process.Blue light blinking even though tray is less than half full . Litter-Robot 4 Recently on my litter robot 4 blue light started blinking even though tray less than half full. Is there a detector that I need to clean or do something? Share Sort by: Best. Open comment sort options ...The blue light is constantly flashing. When reset is pressed the yellow light then flashes. It pinch sensor has been cleaned a… I am having the same issue!!! Tried all of the above and it still doesn't work. Sign out ... My Litter Robot won't reset. The blue light is constantly flashing. When reset is pressed the yellow light then flashes ...If your unit has a blue light bar with partial yellow flashing or the unit will not cycle, this indicates that the scale has been triggered for more than 30 minutes. You will also receive a notification on your phone if you use the Whisker App. Place the unit on a firm, level surface. Avoid soft, uneven, or unstable flooring for accurate weight ...Exact same issue here. It stops upside down with the yellow light flashing insanely fast. Only solution is to unplug it, plug it back in and watch it spin 1.5 rotations and it will be back to normal. Until the next time. And Litter Robot doesn't seem to help. Mine is still under warranty.Kurupt_Introvert. •. Flashing yellow to red means the motor has detected an obstruction or jam. Turn the unit off and remove the bonnet and globe. Check for gear or motor obstruction. Reassemble the unit and verify a proper litter level. Then turn the unit on—if the problem persists, try the Litter-Robot 3 Troubleshooter or contact Whisker ...Preparation. If Litter-Robot 4 has a blue light bar with a yellow blinking light adjacent to the Connect button, this indicates that the unit is in Onboarding mode and waiting to be connected to the app.. You can now proceed with the onboarding process within the Whisker App to finalize connection.. When your Litter-Robot 4 has successfully completed onboarding, the blinking yellow light will ...If the globe is encountering resistance that is lifting it out of position as it cycles, friction will occur between the plastic of the globe and base, causing the magnets in the globe to skip the position sensor which will cause the 3 blinking lights. Out of the box, the Litter-Robot has a silicone lubricant layer that can wear off over time.Community for all things Litter-Robot. Post your experiences, tips, tricks, and hacks. Members Online • NoCheek8681 . Litter Robot 3 yellow light flash just 2 times and die Litter-Robot 3 ... I attached a video to show what it is doing with the yellow light just flashing 2 times after we plug the unit… anyone knows what the issue is? ShareIf your Litter-Robot 3 is displaying a yellow light flashing quickly, this indicates a cycle has been interrupted by the Anti-Pinch safety feature and you will need to inspect the pinch sensor. Inspect the sensors. The purpose of the pinch sensor is to detect if an object is blocking the waste port during the globe rotation."Ready" light goes solid blue. Good to go, right? Came back in an hour later and the blue light for waste drawer full is flashing again, and now it's not rotating when the cat uses it. Just sits there flashing. Pressed "reset" again. Goes back to solid blue for awhile and then within a few minutes starts flashing blue again.Power. Press and release the Power button to turn the robot ON of OFF. The robot will begin a clean cycle when power is turned on. Press and hold, while at the home position, to enter night light setting mode. Cycle. Press and release the Cycle button to start a clean cycle. If already cycling, press Cycle to pause; press again to resume a cycle.Oh my gosh, I've been having the exact same issue!! I purchased the Litter Robot from the canadian site as soon as it became available (October 29th). I've been struggling with the drawer full indicator for weeks and have been too busy to contact support. Like you ArcticThunder, I only have one DFI sensor! It is the one on the right. I noticed this very early after getting my unit and ...Introducing your cat to Litter-Robot. Most likely, your cat will quickly adapt to Litter-Robot. When using in automatic mode, be sure your cat or kitten weighs at least 3 lbs—the weight scale will not recognize cats weighing less than 3 lbs. ... Solid blue, Connect light flashing yellow. Robot in WiFi onboarding mode. Solid yellow. Robot ...
Slow blue light --> fast yellow flashing light. Hi all, I have a pretty old LR 3 (non-Connect, serial # 028957). I replaced the DFI and pinch detect terminals about 1.5-2 years ago and it's been working pretty well since then. A few days ago, the unit stopped cycling entirely. The blue DFI light started blinking even when the tray was empty .... I87 traffic camera
Hello, I am again experiencing this issue: my Litter robot 3 is stuck with a blinking blue light. If I press reset, the yellow light starts blinking fast and the blue goes off. Another press of the reset button and the blue light starts blinking again and so on. I replaced the pinch detector pins and drawer full sensors a year ago (see Litter Robot 3 Keeps Getting Stuck (Help) - #12 by Ebram ...Support request submitted. We strive to respond to all email inquiries within 1 to 2 business days, however higher incoming volumes can affect our response times.We don't recommend buying an automatic litter box, but if you really want one, this model scooped the most waste without jamming. $500 from Litter-Robot. The Litter-Robot III Open Air holds ...Jul 1, 2023 · Hi, I need help with my litter robot 3 please. The blue light is blinking although the waste drawer is empty. The other buttons do not react to pushing except the on/of one. I cleaned the sensors and all robot is clean. Please advise. Many thanks, Maria Then I noticed that the blue light was blinking persistently even the drawer is empty or removed. Then I read the troubleshooting guide, but the problem was not resolved. There is a different situation from other people's. Even the blue light was blinking, after my cat using the LR3, the blinking blue light was changed to RED LIGHT as usual. Litter-Robot 4: Light codes guide. Litter-Robot 4 control panel features 5 buttons and an LED display for easy operation. Blue flashing. If your unit’s light bar is flashing blue, this indicates that the waste drawer is full. Empty the waste drawer, press the Reset button, then press the Cycle button. Learn more. As a quick fix to use your Litter-Robot 3 manually, remove the bonnet, and lift and rotate the globe, mimicking the normal rotation to sieve any deposits for you. ... Update when complete if the light is solid blue or flashing blue or fast flashing yellow, or other. ...The Litter-Robot 3 is equipped with a cat sensor that detects when a cat enters and exits the globe. If the cat sensor has been continuously activated for 30 minutes or more, either by a cat that won't leave the globe or by too much weight in the unit, the timing light will flash red. You will also receive a notification on your phone if you ...The lr3 will blink twice when plugged in to let you know the power is connected. You still need to press the power button to turn it on then it will do an initial cycle. The 2 yellow light blinks are NOT AN ERROR. It's just letting you know it's plugged in correctly. That makes sense, thanks! Any thoughts on the simultaneous red/yellow blinking ...BLUE LIGHT. When you see the blue light flashing on the Litter Robot 4, it signals a full waste drawer. Additionally, paired flashing with yellow WiFi indicates onboarding mode, and with blue WiFi shows app connection issues. for more details, you can read this How To Fix Litter Robot Blue Light Blinking. - Flashing: The waste drawer is full.Litter-Robot 3 is equipped with an anti-pinch safety feature. While cycling, if a potential condition is detected, the globe will stop and reverse direction for 2 seconds. The yellow light will begin flashing quickly (about four times per second), awaiting your action.Reboot your router. Completely close the Litter-Robot app. While the unit is at the Home position with the solid blue light, unplug your unit from the BASE, not the wall. Wait 15 seconds, plug it back in, and allow it to cycle until the solid blue light comes on ("Ready" status). Open the app and follow the steps..
Popular Topics
- Hamilton county sessions court tnLake erie western basin reef map
- Azdot traffic camerasAre animatronics real
- Foot locker greenfield grand riverChicks for sale tampa
- Cub cadet ultima zt1 50 belt diagramChase routing number for brooklyn ny
- Dave and busters win storeScipio talent tree
- Little caesars allen rdSelena villatoro dallas
- Chuco tango gang el pasoHow many pounds in 10 liters